The rear loop

As mentioned earlier, the design of the Pantah isn't the most interesting to my eyes. I wanted to make a unique bike, and there is not any better way of doing that, than to chop the rear frame and make a new rear loop, with a brand new costumised seat to match.

At that time, I worked next to some kind of stainless steel black smith, and yes, I admit it, I borrowed a minor plate of stainless steel, to make a temporary seat, in order for me to ride my bike, while the construction of the rear of the frame was on-going.

I mounted the new rear light on the plate, so that people behind me could see if I applied the brakes, which, I must say, is preferable in traffic. Along with the new seat, came also new tires. Yes, some say that the Firestone Deluxe Champions are over-exposed on cafe racers, but I don't care, I think they look rad, and right now, I would not know, what else to put on my bike.

Just after i snapped the picture above, which you may have seen at my instagram account @morten_mo, I installed my new battery. The S.O.B. had four terminals - two positives and two negatives - and Einstein here, accidentally connected it wrongly, so that I shorted the rectifier... Of course, I only found that out two batteries later - each worth 200$. #FML

The wires were pretty toast...

Preeetty toast indeed.

Before I made the rear loop, I added another classic and over exposed café racer mod. Heat wrap, yes sir. Again, I don't care, I just think it looks awesome. And I must say, that I got it just right at my first ever attempt heat wrapping something.

Another picture below from Instagram.

Now it was time to chop the frame. I have had several thought about this up to this point. Was it worth it, chopping the frame? The answer should prove to be a loud and clear YES.

So then I got the rear loop chopped, and now was the new challenge to have the new loop welded back on. My friend was a welder, but we did not have machinery and so on, so I decided to drive it out to some guys that seriously know what they're doing - The Wrenchmonkees.

www.wrenchmonkees.com

More about them later.

As said, I had a new challenge. I started by sawing over the new rear loop, like below. However, I gave up and yes, drove it out to the wrenchmonkees.

So I put on the temporary seat again, and drove it to Uplandsgade, Copenhagen.

Before then, I took it for a spin in the nice summer time. It isn't always nice in Denmark, so when it is, hit the roads - nomatter how uncomfortable your seat may be.

Well arrived at wrenchmonkees, I parked Francesca next to the co-funder's motorcycle, the monkee #1:

http://www.wrenchmonkees.com/motorcycles/monkee-1.html

I also brought along my new parts for the entire rear loop job.

To speak of my personal oppinion about The Wrenchmonkees... Well, these guys make the sickest looking cafe racers in this part of Europe, and getting them to weld the rear of my bike, would be awesome. It didn't cost much, about 200$, and after that, I had a very nice looking new rear loop.
Every time I go there, they are very helpful with whatever your inquiry is. A nice place to go. Whenever.

Four days later, I picked up my bike.

Super nice job. I was very pleased and satisfied with their work.

All for now. In my next post, I will talk about the making of my custom made seat. Stay tuned.

/Morten

Francesca Ducati

Where we left of some years back on this block, was regarding the disassembly. Since then there has been promises about ressurrections and so on. However, now I have the time to tell my story about Francesca, which I have named this little lady.

Anywho... The disassembly mainly took place at my old apartment, where I had a garage, which was perfect for that.

Two years ago, apparently i had the original mufflers mounted on the bike, however these do not sound of much - they don't do that wonderful engine justice sound-wise.

So I put back on the aftermarket exhaust that I have - a 2-in-1, that sound awesome.

The cone-look makes it quite good looking as well, so it is kind of a win-win-situation, though I have been told that the torque goes slightly down. However, the engine breaths better than with the standard mufflers. It was fairly easy to install.

The reason why the bike is completely torn apart, is that I was fed up with it's original design. It was boring. Ugly. Not good to look at. I thought that I could do better, so I tore it apart and made some minor adjustments.

 Front weel's come off, and all the electrics have been diamantled. I have taken off the fairing too, and all the original clocks.

Looks very naked...

The original rear loop.

Yes, shit's torn apart! But in Denmark we have a saying, that says something like "it has to be bad before it gets good"... This is exactly how it is right here. More to come soon! Among other things, I will show you how I made a new rear loop for the frame, in order to make the frame look nicer, when I had a saddle maker made my new seat for Francesca. Stay tuned.

Resurrection part two

So last year, I wrote that I would update my blog more frequently... We all know how that went! The excuses are many, but I won't bore you with them! However, ms. Francesca is still running, except she is right now in her winter hibernation, in a nice and warm garage!

A lot of things has happened once again within 2013. Some rather big custom motorcycle sites has done articles about this little lady, plus she is now featured on coffee mugs and shirts in the USA. That is awesome!

But I will get back to all that in the months to come, starting from this week, and that is a promise to myself, that I should give this blog some more attention!

Until then, ride safely!

/Morten